Landing Craft 40' 600 hp Landing Craft 2019


[1 de 9 Photos]
Précédente Suivant
Alertez-moi des nouvelles annonces de ce vendeur

Description

New 40' x 142" Aluminum Rear Cabin Landing
Craft

 

(3) independent air chambers

 

Twin 300hp 4 stroke Suzuki outboards

 

3600 LP Onan Generator

 

Commercial RV rooftop AC

 

Enclosed 144"L x 100"W x 8'H
cabin

 

Hydraulic bow gate

 

Located in Missouri

 

Custom built 40’ long x 142” wide rear cabin landing craft hull,
20 degree dead rise, twin outboard, with integrated motor flotation pod, formed
gunnel tops and 3 independent air chambers. 
This hull is custom designed & manufactured for commercial
operations. The air chamber system is
divided into 3 areas. The first being the bow section of the hull. Located forward of the fuel tank section
incorporating 100 % of the front under deck bilge area. The mid section chamber
is designed to access the 300 gallon fuel tank in a completely sealed chamber.
This is achieved by mechanical thru bulkhead fittings and a clever removable
floor section. Access for equipment and
rigging is achieved by thru bulkhead conduits allowing chamber penetration
while maintaining air chamber integrity. 
The rear section air chamber is the main rigging area of the craft. A
deck door opening behind the cabin will allow access to be gained to all other
rigging components, including the holding tanks, water pumps, and other
options. This area is the only area below deck that water can accumulate below
water line, and will be de-watered by multiple bilge pumps. The complete inner deck is self bailing via
gap drains and scupper vents. The sweep out style front door is remotely
controlled allowing entry to a flush work deck throughout the hull for crew
comfort and safety.

 

 

 

SUPER - DUTY AIR (3)
THREE CHAMBER ALUMINUM HULL

 

 

 

§  UNPRECEDENTED AND INCOMPARABLE DESIGN AND
ASSEMBLY TECHNIQUE

 

§        
UNPARALLED HYDRODYNAMIC ACTIVE LIFTING
BOTTOM (M.S.D.P.R.C). UTILIZATION

 

§        
UNRIVALLED PRE-FLEX METAL FORMING PROCESS
UTILIZATION

 

§        
UNYIELDING A.L.E.R.T. STRINGER SYSTEM
UTILIZATION

 

§        
UNCONQUERABLE STRUCTUAL DESIGN &
QUALITY

 

§        
NOTCHED, STEPPED AND VENTILATED FLOTATION
MOTOR POD

 

§        
Unique air chamber pressure checking system
for construction assembly leak detection

 

§        
Length over all (LOA) = 42’ 6' (includes
30” motor pod, no motor, front door closed)

 

§        
142” Beam line-height:200%;text-indent:-0.25in;margin-left:0.5in;">§        
 0.250” Super heavy duty 5086 center keel
plates       

 

§        
(3) Three 144” x 142 x 0.250 AIR CHAMBERS

 

§        
0.190” 5052 Deck Plating, Fuel Tank Cover
& rear access door

 

§        
9 Longitudinal 0.250 6061 Stringers per
chamber (27 total)

 

§        
(5) Three 0.250”X 6” INNER, & (4) Four
0.250”X 4” Outer Full Length Longitudinal A.L.E.R.T. Stringers

 

§        
Sealed self bailing work deck with gap
drains and rear scupper doors

 

§        
(2) Two Full length Integrated structural
flush deck drains with scupper vents

 

§        
0.190” Bow corner posts and tops

 

§        
Heavy duty hydraulic remote power front
gate with 2000 lb capacity

 

§        
28” Vertical from work deck, 0.205” 5052
Pre-Flex formed gunnel one part sides

 

§        
Full length 3” side collision guard
structurally attached to side to air chamber weld seam

 

§        
Front deck: 19' 6" from front of helm
tower to base of bow door

 

§        
125” Wide between gunnels where there are
no bow storage compartments

 

§        
(6) Anchor cleats: two (2) bow, (2) mid
deck, and two (2) stern

 

§        
FULL LENGTH Heavy 20” wide keel doubler
plate (0.500” total thickness )

 

§        
6 full length bottom lifting strakes, three
per side

 

§        
4 Custom 1”x 4” helicopter lifting anchors
(2 front and 2 rear)

 

§        
Custom DSG commercial windows and cabin
door

 

 

 

TWIN 300 HP 4 STROKE SUZUKI OUTBOARD MOTORS AND CONTROLS

 

 

 

36” TIE-BAR DIM

 

NEMA 2000 COMPLIANT

 

3 GUAGE NETWORK: (PORT,
SYSTEMS, STARBOARD)

 

10 SWITCH , 2 POWER POINTS,
FUSED ACCESSORY PANELS

 

SINGLE KEY, DUAL ENGINE SYNC
SYSTEM

 

SPC FLY BY WIRE THROTTLE &
SHIFT

 

DUAL CYLINDER SEA STAR
HYDRAULIC STEERING SYSTEM

 

65 AMP SECONDARY HOUSE BATTERY
CHARGING SYSTEM

 

(2) 24 SERIES START BATTERIES
(ONE PER ENGINE)

 

(2) 27 SERIES DEEP CYCLE HOUSE
BATTERIES SEGRAGATED FROM MOTORS

 

SEE SUZUKI.COM FOR DETAILS         

 

 

 

 

 

3600 LP ONEN GENERATOR

 

 

 

Designed for HD RV application
up to 3600 watts

 

Duel 40 gallon LP fuel tanks

 

Dash mount Remote start and
hour meter

 

Factory silent exhaust c/w
muffler, custom thru hull and back wash flap

 

Automatic “Safety” Transfer
Switch to prevent damage if generator is started with shore power still
attached

 

Spin out oil filter

 

 

 

COMMERCIAL RV ROOF TOP AC AIR CONDITIONER

 

 

 

Designed for HD RV application

 

Automatic thermostatic temp
control

 

5500 BTU

 

Variable speed fan controls

 

 

 

RADIOS AND ELECTRONICS

 

All electronics installed are
NEMA 2000 compatible, in simple terms, all components in the network will
acknowledge each other, and share all information. This has extensive value to
the individual that needs to utilize this information

 

Lowrance BR-24 broadband radar
system

 

Lowrance HDS-10 sonar receiver

 

Lowrance LVR-880 DSC VHF+FM
RADIO

 

Lowrance GPS system

 

Remote hailer and P.A speaker

 

 

 

BOW

 

Two (2) storage compartments located in the forward front corners
inside each bow compartment. Each compartment are designed for quick access
items required on the work deck, ie- Bumpers, throw pillows, life jackets.etc.

 

 

 

 

 

HOSE STORAGE BINS – MID SHIP GUNNEL COMPARTMENTS

 

Two 148” L X 18” W X 20” H front storage bins provided under the
forward bench seating, Integrated into each of the forward gunnel tops. The
storage areas shall extend from the rear of the forward bow compartments to the
front of the fuel fill dividers. Each midship storage compartment will have 2
lids for access, opening restraint cables, and full length toe relief (6”) for
deck worker’s safety.

 

 

 

 

 

HYDRAULIC BOW POWER GATE

 

The front door gate has aluminum hydraulic cylinders, a 12 volt
bi-directional hydraulic wet pack, and a hand held remote control to promote
operation. The gate shall be approximately 84" wide. The gate shall be
designed so the door opening is above the water line, thus enabling the door to
be opened without water entering the boat.

 

 

 

STERN SWIM DECK

 

There shall be a swim deck provided at the stern. The swim deck
shall be approximately 30” long x 95” wide, 
integrated into the motor mount.

 

 

 

ENCLOSED CABIN

 

            The
8 window cabin is located 48” forward the transom (36” usable area)

 

            Fully
enclosed 144”L x 100”W x 80” H insulated cabin

 

            Bow
facing two part windshield with overhang

 

            Port
and starboard front side operating slide windows

 

            Large
aft port side and rear window (32" W x 60" L)

 

            Sliding
entry door with window installed in star side cabin wall

 

            Panic
style locking door latch (open & closed)

 

            3
drawer custom vanity with GFI AC outlet, pump switch, constructed of aluminum
(no wood)

 

            2.5
cubic ft LP/AC RV style Freezer/Fridge

 

            3
burner RV style manual fire LP stove top

 

            Standard
RV style single bay sink, both taps cold, no grey or black water holding tanks

 

            50
gallon under deck fresh water holding tank with RV pressure pump and switch

 

            Custom
12 circuit 12 volt DC with 4 circuit AC breaker/fuse panel

 

            Onboard
12 volt DC automatic house charger with shore power or gen set running

 

            Interior
finish will be 1/8” aluminum white laminate commercial sign board

 

            Standard
RV 44”x 72” upholstered Settee with under seat storage bins

 

            Custom
integrated passenger bench seat and 21” Settee bed extension

 

            Collapsible
twin support table top into settee sleeping configuration

 

            AC
outlet at settee table, vanity front, and front port side of cabin under gunnel
top

 

 

 

BILGE PUMPS

 

            There is a
minimum of two (2) bilge pumps, one 1000 gallon per hour pump located in the
lowest aft

 

possible location of the engine compartment and one emergency (1)
1000 gallon per hour pump located inside the motor mount pod. Each pump is
equipped with a float type switch to permit manual and automatic pump
activation.

 

 

 

 

 

 

 

INTERIOR HULL FINISH

 

            The interior
components of the boat hull is completely covered with scorpion commercial
liner. All horizontal walking and stepping
surfaces are covered with Scorpion Protective Liner. The polyurethane

 

non-skid material has been applied using a spray application, thus
providing an even coverage to all areas.

 

In the color of green, including:

 

-         
Gunnel tops

 

-         
All interior deck surfaces

 

-         
Interior vertical side areas

 

-         
Bow compartments interiors

 

-         
Side storage bins

 

Located in Missouri

 

Price - CALL FOR PRICING